Programming to Acquire CY8C4013SXI-400
Forums: PSoC 4 ArchitectureI'm writing software to create a programmer for this IC. I'm using the PSoC 4 TRM as a reference, which instructs me to reference the "PSoC 4 Device programming...
View ArticleRefHigh and RefLow
Forums: PSoC 4 Architecturei have been using psoc-1. there is refhigh and reflow available for RTD excitation.is that any facility in psoc-4 that fulfith same??because i want two save my both IDAC in...
View ArticlePSOC4200L: External Crystal for USB Application required?
Forums: PSoC 4 ArchitectureHi everyone,I've been scanning through the Cypress PSOC4200L Datasheet and USBFS Documents,but I am not sure if an external cyrstal is required for USB Full Speed Application...
View ArticleProgram Cy8ckit-49-41XX, CY8CKIT 49-42XXX
Forums: PSoC 4 ArchitectureI can not program the devices CY8CKIT-49-41xx and 49-42xxx, the message is "01:50:46 PM - Communication port reported error 'Unable to read data from the target device'."If I...
View ArticleEmulated EEPROM on 4200M (?)
Forums: PSoC 4 ArchitectureHi.I use the CY8CKIT-043 board with CY8C4247AZI-M485 (4200M) chip on it.In the datasheet of 4200M family it's written (on page 5) " Part of the flash module can be used to...
View ArticleADC_CountsTo_Volts on PSoC
Forums: PSoC 4 ArchitectureI'm using PSoC BLE Pioneer,Reading ADC documentation of PSoC I've found this:float32 (uint32 chan, int16 adcCounts)Description:Converts the ADC output to Volts as a floating...
View ArticleClik here to view.
Analog PIN problem
Forums: PSoC 4 ArchitectureHello,So, my question is really simple, i need to connect an analog pin to an ouput analog pin. On the PSoC 4200 BLE CY8C4247LQ*-BL483 it work, but on the PSoC 4000...
View ArticlePWM Pre scaler is not showing consistent behaviour
Forums: PSoC 4 ArchitectureI am using two PWM modules both driven by the same clock.PWM1 period = 99PWM2 period = 9Therefore in each cycle of PWM1, there are 10 cycles of PWM2. Everything works just...
View ArticleDebouncing multiple inputs
Forums: PSoC 4 ArchitectureHello,I have multiple inputs I need to debounce. All inputs are measured by GPIO Interrupt rising edge. I'm essentially counting the positive edges (or pulses) to determine...
View ArticleDEEP SLEEP mode & BLE
Forums: PSoC 4 ArchitectureHello,I have a problem with deepSleep mode. I have Client and Server, that communicate together. When Server sends the new date, it has to sleep for 1 second. if(data_send...
View ArticleClik here to view.
Layout for Radial Slider
Forums: PSoC 4 ArchitectureHi,I am trying to design a new layout for a slider in the form for an arc of a circle. I have four pads on the arc. I have configured this to be a radial slider. But when I...
View ArticleUnknown CYBLE Stack Events
Forums: PSoC 4 ArchitectureHi AllWhile debugging my project I am receiving two BLE Stack events, 0x104 and 0x105.The project works OK but I am curious as to what they mean.Does any one know their...
View ArticleModifing the Bootloader UUID
Forums: PSoC 4 ArchitectureHi AllI am implementing a bootloader into my project and I would like to use a different UUID from the one used in the various examples.Currently the Service UUID is...
View ArticleClik here to view.
[Resolved] Max input voltage on ADC
Forums: PSoC 4 ArchitectureHi all,I'm designing a board, using the SAR ADC of the PSoC4 with an external Vref of 2.5V. I'm measuring a 10k poty ranging from 0V to 2.5V when it's connected, that's all...
View ArticleI2C With PSoC4
Forums: PSoC 4 ArchitectureHi AllI apologize for being active on forum after a very long time. Anyways, I am currently working in a direction to test I2C Master and Slave in a single PSoC4 - 049 42xx...
View ArticleWhat is needed.......
Forums: PSoC 4 ArchitectureIf I were to build my own circuit board and would like to incorporate a cyc8c, like the one on the PSoC 4, what components and design circuitry would I need? What software...
View ArticleUART issue with KITPROG-043
Forums: PSoC 4 ArchitectureHi All, I am using KITPROG-043 and I have a UART component that prints DEBUG messages on Pins P7.0 and P7.1. As I have detached the KITPROG from PSoC4 I need to use the Pins...
View ArticleI2C Scan
Forums: PSoC 4 ArchitectureHi All,I'm using the EZ-BLE modules CYBLE-214009-EVAL and CYBLE-014008-EVAL with CY8CKIT-042 PSoC® 4 Pioneer Kits.I'd like to scan for any/all I2C devices connected to my...
View ArticleClik here to view.
opamp and sar adc componant error
Forums: PSoC 4 Architecturewhen i try to put opamp and sar adc on schematic than i got this below message attached in image and i cant put component on schematic.how can i resolve this error??...
View ArticleAbsolute Mouse Coordinates in USBFS
Forums: PSoC 4 ArchitectureHi folks,I am currently working on a touch application which should use absolute coordinates.How can I change the relative coordinates into absolute coordinates in USBFS?I...
View Article