Timer with ECO clock input
Forums: PSoC 4 ArchitectureHiAssociated with my other posting about clock behavior, how exactly do you use the ECO clock as an input to a timer?If I select HFCLK as the existing clock source in a clock...
View ArticleClik here to view.
IIC communication error. SCL and SDA keeps low
Forums: PSoC 4 ArchitectureHi,I am using a master MCU to communicate with touch board which is powered by CY8C4014LQI-422. The master uses io simulated iic and CY8C4014LQI-422 uses EZI2C. EZI2C is...
View ArticleClik here to view.
Display BMP images on TFT 240 * 320 ILI9341
Forums: PSoC 4 ArchitectureHi recently I have been working on TFT INI9341 and facing problem with displaying bmp images on TFT screens. Library that I used is...
View Articlerefmux in psoc-4
Forums: PSoC 4 Architecturei have been using psoc-1.there is a reference voltage selection.but i cant find it in psoc-4.can anyone tell me where it is available in psoc-creator software???
View ArticlePower Mode
Forums: PSoC 4 Architecturecan i use pwm and adc in sleep,deep sleep and hibernate Mode???
View Articlepower Drop
Forums: PSoC 4 Architecturei have psoc-4 (CY8C4245-482) stanlone ic.i give external 5 volt between vdd and ground and i check voltage across vdd & ground pin with multimeter then it show only 2.6...
View ArticlePRoC 4 UART receive problem
Forums: PSoC 4 ArchitectureQ1: I have problem when I am writing a UART Tx and Rx program for the PRoC 4 (CYBL10573) device. I found that all the example project used a function "UART_UartGetChar" in...
View ArticleClik here to view.
Making a Mux/Dmux use Non-BUS Select Inputs
Forums: PSoC 4 ArchitectureHere is a solution to driving a 1/4 Mux from a Control Register without having to use a BUS.There are many times in which we need to drive a mux's select input without using...
View ArticlePSOC4 motor kit (CY8CKIT-037) current limitation
Forums: PSoC 4 ArchitectureWe are evaluating using the PSOC in our motor application. The kit is quite nice and well built. We'd like to test higher current and the power supply is only 24v @ 2.1amp....
View ArticleLocate array onto flash row
Forums: PSoC 4 ArchitectureHiIs it possible to locate a static const array to the start of a flash row (that is, to a 128 byte boundary)?I'm using a PSoC4BLE (that doesn't support emulated EEPROM) and...
View ArticleClik here to view.
How can I gain access to SCB HW_UART RX/TX without going off-chip
Forums: PSoC 4 ArchitectureHas anybody ever had a need to connect the serial stream (both Tx & Rx) from a SCB Hardware Uart to internal logic for mux-ing demux-ing before sending to an external...
View ArticleClik here to view.
[4M] Silly project: RAM -> GPIO Port with DMA
Forums: PSoC 4 ArchitectureHi,I'm doing a silly project where i have an array of random numbers and i would like to transfer each element of the array to the GPIO Port 1 with DMA, each transfer must be...
View ArticlePWM in deep sleep
Forums: PSoC 4 Architecturecan i set PWM in deep sleep mode in psoc-4???if yes than how can i set in programming ???
View ArticleClik here to view.
Analog routing error
Forums: PSoC 4 ArchitectureHi all,I have spent some time fighting this problem. I have tried many things, but I am still missing something. "Unable to find solution for analog routing". Can anyone...
View ArticleClik here to view.
Help newbie to understand design structure (SPI/I2C)
Forums: PSoC 4 ArchitectureHi :) I am starting a project and I need some advice on how to start it in the best way. I have good nowlegde in overall programming and basic knowledge in posc architecture....
View ArticleKeyPad using Capsense CY8C4245
Forums: PSoC 4 ArchitectureI want to design matrix key pad of 48 keys. Currently I am using only One Matrix Button. Is it recommended to use two Matrix button? If I use two matrix button then there...
View ArticleClik here to view.
Problem in Idac
Forums: PSoC 4 Architecturei attached my project.i cant got current output on my decided pin.can you tell me where i did mistake???i got only 0.1uA current for any value of idac.Attachments: Download...
View ArticleHardware dual input counter
Forums: PSoC 4 ArchitectureHi everybody! The project I'm currently working on requires a counter with the ability to increment or decrement its value based on two non periodic clock/count direction...
View Articlecomponent
Forums: PSoC 4 Architecturehow can i add any new componant in psoc creator 3.3???
View ArticleClik here to view.
two idac parallel for higher resolution
Forums: PSoC 4 Architecturei found this example project on website. i show PIDAC in this attached file.whether its working on psoc-4 for higher resolution?? Attachments: Download AN64275_0.zip
View Article